Top 10 typical forklift mishaps ， forklift operation must focus on these issues ！.

Do not undervalue the forklift at the workplace. If the operation is bad, there will be major mishaps in mins, and there are lots of crashes entailing forklifts.

Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead might not be discovered, leading to a moving mishap.
Situation 2: In order to preserve the balance of the forklift when lifting heavy items, the staff members used their body weight as the weight, which virtually created casualties.
Instance 3: The size of the forklift cargo exceeds the allowable size of the course and holds on the roadside shelf, which almost causes an crash.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Instance 5: The forklift motorist did not discover the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the workers illegally, the forklift driver does not put on the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Instance 7: The forklift chauffeur did not use a safety belt and dropped from the car when it surrendered and was squashed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after confirming that there are no challenges that hinder the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge must be risk-free before beginning.
3. When the forklift begins with a tons, the driver must first verify that the lots is steady and reliable.
4. The begin needs to be sluggish and constant.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be kept at 300mm-400mm, and the pole should be slanted in reverse. .
2. Do not lift the fork too expensive when driving. When entering and leaving the task website or while driving, be careful that there will be no barriers overhead. When the load is taking a trip, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After dumping, the fork should be reduced to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued first. High-speed doglegs are banned. High-speed sharp turns will trigger the automobile to shed side security and topple. .
5. When the forklift is downhill, it is strictly forbidden to shut off the flame and slide, and it is prohibited to brake instantly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and need to maintain a particular safety and security range from the vehicle in front. .
7. When the forklift is running, the load must be in the lowest setting that does not hinder the driving, and the gantry must be correctly slanted back. The load shall not be increased other than when piling or packing. .
8. The height of the tons have to not block the driver's sight. In unique circumstances, when the item impacts the forward vision, drive at a reduced speed when turning around.
9. It is prohibited to turn on the ramp, neither to drive across the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it needs to drive securely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is prohibited for personnel to base on the fork to hold items and play a stabilizing role. .
12. If troubles are located, they will certainly be fixed and reported in a prompt way, and they will certainly never ever run with ailments or conceal them.

filling and unloading.
1. When fork-loading products, the distance in between both forks must be adjusted as needed to make the load of the two forks balanced and not manipulated, and one side of the item should protest the shelf. .
2. It is forbidden to work with a single fork or make use of a fork top or draw. In unique scenarios, security warning signs have to be set up to advise bordering pedestrians. .
3. In the process of loading and dumping products, the forklift should be stopped with the brake. .
4. The speed of the vehicle must be slow and constant. Beware not to roll the wheels on the dunnage, so as not to extend the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it must be noted that the fork pointer ought to not touch various other goods or items. The lots should be supported with minimal back tilt of the gantry to ensure that the lots does not slide in reverse. The pole can be tilted ahead a little when the load is reduced to permit easy placement of the tons and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to utilize the brake inertia to slip, put, round or roll items. .
10. It is not permitted to make use of forks to select, transform pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for special circumstances, such as the chauffeur does not leave the car's line of sight and does not exceed 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, examine whether the pressure and temperature are normal.
5. After the forklift is running, the exterior leak ought to also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must check prior to leaving the cars and truck;.
2. When you come across someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above Stand-on Electric Pallet Stacker the ground;.
5. The transforming ought to not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow-moving and uniform, and no activating the slope is allowed.
7. Do not drive throughout the gradient. When the gradient is greater than 10%, the automobile should be driven in reverse when going downhill;.
8. When the forklift employees carry the goods and move on, if they experience huge or heavy products and go to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be complied with in the procedure.
1. Single fork operation is not permitted.
2. It is not allowed to raise the goods for cross country driving.
3. It is not allowed to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not permitted to use inertia force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of Stand-on Electric Pallet Stacker the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844